workshop 2 Flat Macrame Aug 24 Written By Yoko Onishi Flat macrame bracelet Preparation Step 1 cut three cords around 50 cm long each Step 2 Thread cord 1 through all beads Step 3 Set cord 1 on the clip board or table, placing all beads in middle of cord 1. Step 4 Move the last bead to the side and place the middle of cord 2 underneath cord 1. Step 5 Bring the right side of cord 2 to left side over cord 1. Step 6 Bring the left side of cord 2 over. Step 7 Bring the left side of cord 2 to right side under cord 1 and over the right side of cord 2. Step 8 Pull both side of cord 2 to knot.This is halfway of the flat knot. Step 9 Now, do exactly same thing only opposite.Bring the left side of cord 2 to right side over cord 1. Step 10 Bring the right side of cord 2 over Step 11 Bring the right side of cord 2 to left side under cord 1 and over the left side of cord 2. Step 12 Pull both side to knot.This is one flat knot. Step 13 Move back the bead. Step 14 Repeat Step 5-12 Step 15 continue repeating step 5-12 Step 16 Start plaiting( French Braid ) after about 10 knots. Step 17 Repeat step 4-16 on the other side. Step 18 Measure widest part of your hand. Step 19 Measure your bracelet.Make it around 2cm longer than length of your hand. Step 20 Make simple knots on both end and cut off left over cords. Step 21 Keep one of left over cord from step 20 Step 22 Make flat knots on plaited part of bracelet Step 23 Cut off left over parts of the last cords.Now you should be able to slide the plaited part of bracelet to adjust the size. MacrameWorkshopDIYMacrameHow to MacrameBraceletChakraStone Yoko Onishi
workshop 2 Flat Macrame Aug 24 Written By Yoko Onishi Flat macrame bracelet Preparation Step 1 cut three cords around 50 cm long each Step 2 Thread cord 1 through all beads Step 3 Set cord 1 on the clip board or table, placing all beads in middle of cord 1. Step 4 Move the last bead to the side and place the middle of cord 2 underneath cord 1. Step 5 Bring the right side of cord 2 to left side over cord 1. Step 6 Bring the left side of cord 2 over. Step 7 Bring the left side of cord 2 to right side under cord 1 and over the right side of cord 2. Step 8 Pull both side of cord 2 to knot.This is halfway of the flat knot. Step 9 Now, do exactly same thing only opposite.Bring the left side of cord 2 to right side over cord 1. Step 10 Bring the right side of cord 2 over Step 11 Bring the right side of cord 2 to left side under cord 1 and over the left side of cord 2. Step 12 Pull both side to knot.This is one flat knot. Step 13 Move back the bead. Step 14 Repeat Step 5-12 Step 15 continue repeating step 5-12 Step 16 Start plaiting( French Braid ) after about 10 knots. Step 17 Repeat step 4-16 on the other side. Step 18 Measure widest part of your hand. Step 19 Measure your bracelet.Make it around 2cm longer than length of your hand. Step 20 Make simple knots on both end and cut off left over cords. Step 21 Keep one of left over cord from step 20 Step 22 Make flat knots on plaited part of bracelet Step 23 Cut off left over parts of the last cords.Now you should be able to slide the plaited part of bracelet to adjust the size. MacrameWorkshopDIYMacrameHow to MacrameBraceletChakraStone Yoko Onishi